Craig excavator buckets are designed and built to meet your specifications. Superior quenched and tempered Brinell 400 steel is used in all wear areas.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for side cutters or wear shrouds
• Optional Hard-Facing available
• Various ground engaging tools available to meet your specifications
• Pin-on hook-ups are align bored to OEM tolerances
• Enclosed lift ring standard

The Craig Integrated Thumb Trenching Bucket is based on our Direct Link Hydraulic Thumb (EX-CUT) and Heavy Duty Trenching Bucket (EXB-HD). Hanging the thumb from the bucket rather than the stick pin allows the excavator to completely free itself from the bucket and thumb in just seconds. The thumb cylinder is intended to be removed from the excavator stick, allowing for maximum operator visibility when using other attachments.

• Available in Wedge Lock lugging only
• Comes pre-drilled for side cutters or wear shrouds
• Various ground engaging tools available to meet your specifications
• Enclosed lift ring standard
• Thumb has up to 120° of gripping rotation
• Thumb and bucket teeth inter-mesh

With its low profile design, curved cheek plates and active attack angle, the Craig Quik Fill bucket is designed to minimize surface friction and maximize cycle time efficiency when loading and unloading the bucket.

The lengthened shell floor promotes smooth loading and unloading with minimal wasted movement. Instead of using breakout force to fill the bucket by curling the attachment, the Quik Fill bucket is designed to be pulled towards the machine – shaving material into the bucket in a smooth motion. This motion eliminates partial fills and excess spillage while also leaving the bucket closer to the open position to allow quicker dumping of the material.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Longer hooks for easier alignment
• Quik Fill option available for HD, XHD and SS class buckets

Craig offers all digging buckets with the option of low pin lugging. Used exclusively on machines equipped with pin grabbers. Recessed pins decrease tip radius for added breakout force over conventional full height lugs.

• Available on Quik Fill and Standard profile buckets
• Pin bosses are align bored to OEM tolerances

The ultimate trenching bucket for excavators working in the most extreme applications. The Craig Mega Armour Severe Service Trenching Bucket features extensive plating and wear components in key areas to reduce wear in high abrasion, high impact job sites.

• Top and bottom sidebar protectors are interchangeable to improve wear life
• Designed to protect the edges of the three piece runners
• Protects key area where the base edge is welded to the side cutter
• Internal Weldox 100 beams reinforce the bridge section of the bucket
• Designed to protect from base edge scalloping
• Key wear areas made of Hardox 450 for increased life and durability

The excavator sand bucket has a scoop shape with a flat bottom to sit on the ground for easy attachment while the shape is perfect for scooping materials like sand and fine gravel.

• Reduced surface area and lack of GET allows for easy penetration through for soils
• Flat BTM design allows for detailed grading during pipe laying operators
• Open top prevents soils from “air locking” and suctioning to inside of bucket
• Bolt on edge (optional)

The rock slab bucket expertly gets under layers of rock to break and remove chunks and slabs of rock. The half arrow tip and smooth edge makes it easy to slip between layers of rock to pry and lift slabs.

• Made entirely of high strength and high wear plate
• Continuous/solid plate design from hookup to the underside of the smooth edge for maximum strength.

The Craig Skeleton Rock Bucket is designed for separating rocks and other large materials from loose soil. The SR bucket for excavators is made of durable steel to last tough applications. Slots sift loose material to separate rocks.

• Bucket ribs are made of high abrasion steel for added strength and durability.
• Designed to sift dirt, gravel, and debris
• Bottom of bucket features AR 400 wear plate runners and choice of GET
• A range of custom opening/spacing of the bucket ribs are available to suit debris sorting

Craig Severe Service Buckets are specifically designed to meet your toughest applications. Superior 400 Brinell quenched and tempered steel is used in the mainsheet, end-plates, horizontal wear bars and base edge.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for side cutters or wear shrouds
• Optional Hard-Facing available
• Various ground engaging tools available to meet your specifications
• Pin-on hook-ups are align bored to OEM tolerances
• Enclosed lift ring standard

The v-shape trench bucket is the perfect bucket for pipe laying in rocky/fractured ground conditions. The v-shape of the bucket also reduces the amount of bedding material that will be required in the trench thus reducing the cost to install pipe. All teeth engage the ground at the same time which leaves a smooth trench bottom.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Complete with Adco style GET

Extra Heavy Duty Buckets feature thicker G40 steel throughout their construction – including thicker Brinell 400 wear plate on the runners and side front plate.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging
• Comes pre-drilled for side cutters or wear shrouds
• Optional Hard-Facing available
• Various ground engaging tools available to meet your specifications
• Pin-on hook-ups are align bored to OEM tolerances
• Enclosed lift ring standard

Available for all makes and models of hydraulic hammers and plate compactors.

• Available in Wedge Lock, Pin-on, S Series, or Manual Bar Lock lugging

The Craig Convertible Wedge Lock Coupler features a light weight, low profile design that maintains your machines OEM tip radius while offering a quick coupling system. Available as either a hydraulic or manual coupler, both configurations share the same chassis allowing them to be easily switched to either configuration at any time with a Craig supplied kit.

• Offers a solid, safe and secure hook-up – self adjusts for coupler wear
• Works with all Craig Wedge Lock lugging for the same weight class
• Manual configuration features a lock plate to keep bolts from turning out
• Double redundant safety pins to ensure attachment remains in place in the event of hydraulic pressure loss on hydraulic configuration
• Converts from Manual to Hydraulic in minutes
• Hydraulic circuit required on machine stick to operate hydraulic configuration
• Optional safe working load rated lift eye available

We have taken our proven convertible wedge lock coupler and made it ISO13031 compliant. It continues to provide a light weight, low profile design that maintains your machines OEM tip radius while offering a quick coupling system so you can switch between attachments without having to leave the cab. The coupler has an automatic safety lock that ensures continual engagement even in the event of loss of hydraulic pressure.

• Offers a solid, safe and secure hook-up
• Self adjusts for coupler wear
• ISO 13031:2016 compliant coupler design when sold with a Craig “fully independent coupler kit” (hydraulic lines and control valve run back to engine compartment and hydrauilc tank.)
• Optional safe working load rated lift eye available
• Visual locking indicator to identify attachment is engaged
• Automatic safety locks, does not require safety pins to be inserted after engaging attachment.
• Coupler can be converted back to a manual version if needed (optional manual kit required).
• Made in North America

The Craig TrueGrip pin grabber has a simple and reliable design. It features 2 independent locks and has visual safety indicators that allow the operator to ensure both the front locking knuckle and rear latch are engaged. Works with most OEM Coupler Kits (confirm with Craig) or can be supplied with a Craig hydraulic kit.

• Attachments can be picked up in forward and reverse orientations
• Features a multi-pin design to pickup attachments from most OEMs in the same machine category
• Minimal moving parts —single cylinder design that requires no greasing
• Includes one set of non-hardened attachment pins
• Uses two line coupler kit system
• Coupler is designed with machine specific hookup - no loss in attachment rotation
• Dual independent locks to ensure attachment is retained even if the coupler loses hydraulic pressure
• ISO 13031:2016, EN 474, and AS 4772 COMPLIANT coupler design (see hydraulic kit options below)
• Complete with rated lifting point installed
• Patented design
• Made in North America